EPSON ARTISAN 700 800 99

Product Description

No more Ink Cartridges purchase, No more Cartridges replacement. Refillable ink cartridges/ink reservoirs enable countless refills.

Pre-filled with premium UV Resistant dye based Ink. Quick and Easy installation. You will be printing in minutes. 80% Saving on individual Inkjet Cartridge. No Leaking or Clogging Pre-Assembled Environmentally Friendly Permanent Chip. Auto-reset chipsets automatically reset the cartridges so there is no need to utilize a chip resetter nor take the cartridges out of the printer to refill. Product Detail The CIS(Continuous Ink System) consists of a high-capacity ink reservoir (same as using between 8 ~ 10 ink cartridges per color) that is attached to a cartridge via secure tubing. The tubing acts as a vacuum to extract ink from the reservoir and keep the cartridge full of ink. Because of the large reservoir capacity, you can print for an extended period of time without running low right away. There is a red line on the reservoir to indicate when it is time to refill.

Each CIS comes complete with easy-to-follow instructions, ink, and all accessories needed to successfully use the system. The included UCI cartridges have a permanent smart chip already installed, which will automatically reset itself when your printer power is turned off (for 5 seconds) and turned back on. No mess! No leaking!

After using ujp the ink in reservoir, you can refill the resivoir with a refill kit sold separately. The refill kit contains SIX bottles.

For your convenience, there is a filter built into the ink tank, to prevent outside agents from contaminating and/or affecting the quality of your prints.

Additional Information CArtridge No. T098120 : Black T098220 : Cyan T098320 : Magenta T098420 : Yellow T098520 : Light Cyan T098620 : Light Magenta Instruction Manual Instructional Manual Continuous Ink System for use in Epson Artian 700 All-in-One Printer & Artian 800 All-in-One Printer Before using this product, please read and follow the instructions carefully. Conduct Parts Check: 1.Accessories Continuous Ink System (1) Air breather plugs (6) Syringe(1) Square adhesive pad(2)

2.Set-Up Continuous Ink System(CIS) a. Before installation, lay out all your parts in front of your printer.

b. Check your system for any leakage, and make sure your tubing system is tightly connected and straight.

c. Place the CIS ink tank on the same horizontal level as printer, The ink tank has two chambers per color, the front chamber is to hold the ink and the rear chamber is to control the flowing pressure. It is important that the rear chamber contains only a small amount of inks(as little as possible). The ink should reside in the front chamber. Make sure the ink tank plugs are tightly closed, tilt the ink tank forward to make the majority of the ink flow into the front chamber if the rear chamber has some excess ink.

d. Place the CIS on the left hand side of the printer as shown and keep it at the same level as the printer.

e. Hold down the ink tank with one hand and unplug the original air stoppers as shown make sure to save these for later use.

f. Install the Air Breather wider part into the ink reservoir tank, making a snug fit.

Caution : Make sure not to push the breathers too tight as it could crack the tank. Also when removing the air breathers from the tank use caution to avoid cracking. 3.Cartridge Installation a. Unplug the printer power.

b. Ensuring that the colors correspond, push the cartridges all the way down in the compartment just as you would do with the original cartridges.

4.Tube Adjustment and Positioning a. Place the square shaped adhesive on the top left side of the printer and insert the tubing.

b. Close the cover and push down on it slightly so that it closes as much as possible.

c. Turn on the printer and make sure the system moves smoothly.



5.Refilling Ink When the ink levels reach the indicator margin (sticker on the ink tank with red line. the ink tank system has reached its low level line and needs to be refilled.

Follow these steps: 1. Gently remove the air breather plugs in order to have more filling room. 2. Remove plugs off of the filling hole and refill the proper color of ink into the corresponding ink tank (use towel to wipe off any spillage) 3. Make sure you use the specially designed inks Low Foam ink for the CI System as they are specifically designed for optimal results.

NOTE : When removing the CI System, remove cartridges and put tape or a napkin over dispensing hole. Printer and ink tank MUST remain at the same level (not higher and not lower).

6. Attention 1. After installing the CI System, do not remove the cartridges unless it is necessary. If cartridges are removed, Immediately place cartridges upside down with ink exit holes facings up to avoid leaking. If cartridges are removed for more than an hour, please cover ink exit holes with tape

2. When you are printing do not move the ink tank up or down. Keep it stable and at the same level as the printer.

3. Store at 15-35 degrees Celsius. 4.The ink and cartridge flow have been designed and tested to function as a system. We recommend you use the specially designed ink Low Foam Ink in the CIS for optimal results.

7. Caution 1. Do not ingest ink and keep out of reach of children. 2. Do no leave under sunlight or in extreme weather conditions. 3. Do not drop ink tank or handle roughly.

8. When you get the "Replace Cartridge" message follow these steps. a. Click on the "How to" button. b. You will get a screen that tells you to use Epson ink cartridge, click on the "Next" button. conditions. c. The 2nd screen tells you to remove cartridges from the package, click on the "Next" button. d. The 3rd screen lets you know it's going to move the printheads to replacement position, click on the "OK" button. e. The 4th screen tells you to remove cartridge, click on the "Next" button. f. The 5th screen tells you to install cartridge, when you get this screen the first thing you need to do is push the Reset button that is on top of the cartridges. Push this button once and then click on the "OK" button. g. The next screen should show you that the link is charging, when it is done charging click on the "finish" button.